JIANA ZHILIAN Wire Harness · Dongguan, China
Application notes

Wiring a camper van solar system: panel to battery, connector by connector

A practical walk through a 12 V camper solar install — which connector at each junction, what each is rated for, and the three places the wiring usually goes wrong.

7 min read

A camper solar installation is a chain of four or five junctions, and each one uses a different connector for a reason. Getting the chain right is mostly about rating each link honestly.

The chain

Solar panel  →  MC4  →  cable run  →  MC4  →  Controller
Controller   →  screw terminal / Anderson  →  House battery
House battery →  Anderson 50 A  →  Distribution / inverter
Distribution →  cigarette socket / USB / lighting

Junction by junction

1. Panel to cable — MC4

MC4 is the only connector in this chain with a genuine IP67 rating when mated, which is why it belongs on the roof. Rated 30 A; almost every camper panel is well under that.

Watch for: MC4 connectors are made by many factories and dimensionally similar but not always identical. Mixing brands can produce a joint that looks mated but is not fully seated, which is both a resistance and a water-ingress problem.

2. Cable run through the roof — MC4 to MC4

The extension run. Keep it as short as practical: voltage drop on 12 V systems is brutal. A 6 m run of 4 mm² at 15 A loses around 0.7 V.

Watch for: glanding at the roof entry. The MC4 is sealed; the point where the cable passes through the roof shell is not, unless you use a proper cable gland.

3. Controller to battery — screw terminal or Anderson

Most controllers have screw terminals, so this is often a bare-wire or lug connection. Where you need a disconnect, an Anderson 30 A or 50 A housing is the usual choice.

Watch for: fusing. There must be a fuse at the battery end of this run, sized to the cable, not at the controller end.

4. Battery to distribution — Anderson 50 A

House banks and inverter feeds land here. 50 A housing on 8–12 AWG.

Watch for: sizing by peak rather than continuous. A 2000 W inverter at 12 V draws about 170 A at full load — that is not an Anderson job at all.

5. Distribution to accessories — cigarette sockets

Convenience connectors. A fused cigarette plug caps the branch at 10 A regardless of what is upstream.

Watch for: assuming a 50 A source makes a 50 A accessory circuit. It does not.

The three places it usually goes wrong

1. Rating the run by the source. People fit a 50 A Anderson at the battery and then run 16 AWG to the accessory, expecting 50 A. The assembly is rated by the weakest link.

2. No fuse at the battery. A short in the run between battery and controller, with no fuse at the battery, is a fire. Fuse at the source end, always.

3. Mixing sealed and unsealed connectors outdoors. An MC4 on the roof feeding an SAE connector in a wet locker defeats the MC4’s IP67 rating at the SAE end.

A note on adapter leads

Converting between these connector families is normal — MC4 to Anderson, Anderson to cigarette plug, SAE to EC5. Every adapter carries a rating, and it is always the weaker end:

Adapter Rating Limited by
MC4 → Anderson 30 A 30 A MC4
MC4 → cigarette plug 10 A Fused plug
SAE → SAE extension 20 A SAE
Anderson 50 A → cigarette plug 10 A Fused plug

Plan the chain so the adapter is not the bottleneck where it matters.

Frequently asked

Can I skip the controller? Only for a very small panel used as a maintainer, and even then a controller is inexpensive insurance against overcharging.

Is 4 mm² enough for a 400 W panel? At 12 V a 400 W panel is around 33 A at peak. 4 mm² (roughly 12 AWG) is marginal at that current over any distance — go to 6 mm² or run at a higher voltage.

Should the panel side be fused? The panel cannot deliver more than its short-circuit current, so a fuse on the panel side protects the cable against fault current from the battery, not from the panel. Fuse at the battery end of the controller run.


Tell us the panel wattage, the bank voltage and the run lengths, and we will specify the gauge and the connector at each junction.

Need this built to your drawing?

Send the drawing, the gauge and the annual volume — we quote within one working day and sign an NDA before drawings change hands.

Request a quotation

← All technical notes