Wire gauge and current: an AWG to mm² ampacity table for harness design
How AWG, mm² and ampacity line up, why the same 12 AWG lead can be rated 20 A or 35 A depending on the connector, and how to pick a gauge without over-specifying.
Wire gauge is the first number anyone asks for and the one most often over-specified. Too thin and the conductor runs hot; too thick and you pay for copper you cannot bend, and you discover the connector will not accept the wire anyway.
AWG to mm² — the conversion you actually need
| AWG | mm² (nominal) | Typical use |
|---|---|---|
| 22 | 0.33 | Signal, small sensors |
| 20 | 0.52 | Signal, LED, low-power |
| 18 | 0.82 | Small 12 V loads, up to ~10 A |
| 16 | 1.31 | General 12 V, up to ~15 A |
| 14 | 2.08 | 12 V power, up to ~20 A |
| 12 | 3.31 | Battery leads, up to ~30 A |
| 10 | 5.26 | High current, up to ~50 A |
| 8 | 8.37 | High current, up to ~70 A |
| 6 | 13.3 | Storage and traction |
| 4 | 21.2 | Heavy DC, busbars |
| 2 | 33.6 | Battery bank main feeds |
The “up to” figures above are free-air guidance for short runs at moderate ambient. They are not a rating — the rating belongs to the finished assembly.
Why the same 12 AWG lead can be rated 20 A or 35 A
Because the assembly rating is set by its weakest element, and that is usually the connector:
- An XT60 on 12 AWG is rated 35 A at ΔT ≤ 85 K
- The same 12 AWG terminated into a 12 V cigarette plug is rated 10 A, because the plug and its fuse are the limit
- The same 12 AWG into an MC4 photovoltaic connector is rated 30 A, because that is the MC4 limit
The copper did not change. The assembly rating did.
This is why our adapter pages quote things like 30 A max (limited by the MC4 end) —
the number describes the assembly, not the wire.
Choosing a gauge
Work backwards from the constraint that binds first:
- Continuous current. Pick the gauge whose ampacity comfortably exceeds your continuous load with margin for ambient temperature.
- Connector acceptance. Check the maximum gauge the connector body accepts. An XT60 will not take 8 AWG; an XT150 body will.
- Voltage drop over the run. On long runs, voltage drop binds before thermal ampacity does. A 5 m run at 30 A on 12 AWG loses over a volt — roughly 3% of a 12 V system — before any heating concerns arise.
- Mechanical. Thin wire in a vibrating installation work-hardens and fails at the termination. Below 22 AWG in a moving application, consider a flexible stranded construction rather than a solid conductor.
Insulation is a separate decision
Conductor gauge gets the attention; insulation usually decides whether the assembly survives.
| Insulation | Temperature | Flexibility | Typical use |
|---|---|---|---|
| PVC | 70–105 °C | Moderate | General internal wiring |
| XLPE | 105–125 °C | Moderate | Automotive, industrial |
| Silicone | up to 200 °C | Excellent | Battery compartments, tight bends |
| PUR | 80–90 °C | Excellent, abrasion resistant | Cable track, moving axes |
| PTFE | 200 °C+ | Stiff | High temperature, chemical |
Silicone is the usual choice inside a battery enclosure: it tolerates the combination of ambient heat and conductor heating that would soften PVC, and it stays flexible at low temperature in winter.
Frequently asked
Is thicker wire always safer? No. Beyond the connector’s acceptance limit it simply does not fit. It also adds weight, cost and stiffness, and a stiff lead transmits more vibration into the termination.
Should I use the peak or continuous current to pick the gauge? Continuous. Peaks are handled by thermal mass for a short duration; the steady-state current is what the assembly has to live with.
What about voltage rating? Wire voltage rating is separate from ampacity and matters on high-voltage DC systems. 500 V DC is common for XT-series parts; above that, specify the assembly voltage explicitly.
If you tell us the continuous current, the run length and the connector you want, we will come back with the gauge, the assembly rating and the voltage drop — rather than just a wire size.
Need this built to your drawing?
Send the drawing, the gauge and the annual volume — we quote within one working day and sign an NDA before drawings change hands.