JIANA ZHILIAN Wire Harness · Dongguan, China
Selection guides

LCB30 vs LCB40 vs LCB50: choosing a latched two-pin connector

Three sizes of the same latched body. What the datasheet actually confirms for LCB30, what we will not claim for LCB40 and LCB50, and how to decide between them.

5 min read

The LCB family is a latched two-pin connector for battery-to-controller and motor-to-controller runs — the places where a friction-fit XT is a liability and a bolted connection is inconvenient. Three sizes exist: LCB30, LCB40 and LCB50.

What the datasheet actually says

We publish figures only where a supplier datasheet supports them. That is why this table is uneven:

LCB30 LCB40 LCB50
Continuous rating 35 A @ 12 AWG (4.0 mm²)
25 A @ 14 AWG (2.5 mm²)
Gauge dependent Gauge dependent
Rated voltage 600 V DC — —
Contact resistance ≤ 0.6 mΩ — —
Insulation resistance ≥ 2000 MΩ — —
Operating temperature −40 to +120 °C — —
Mating cycles 50 — —
Retention (latched) ≥ 8.0 kg — —
Contact material Copper, silver plated Copper, silver plated Copper, silver plated
Housing PBT GF30, orange PBT GF30, orange PBT GF30, orange

The dashes are not an omission in this article — they are the honest state of our documentation. LCB40 and LCB50 share the body design, the contact plating and the housing material, but we have not been given a datasheet that states their ratings, so we will not print a number we cannot support.

If you need a figure for LCB40 or LCB50, ask us and we will obtain it from the manufacturer in writing.

Why the LCB30 rating is tied to gauge

35 A at 12 AWG and 25 A at 14 AWG, both at ΔT ≤ 40 K. The 40 K criterion is stricter than the 85 K used on XT-series parts, which is why the LCB numbers look conservative for the size of the housing.

A stricter rise means a cooler running connector, which matters inside a battery enclosure where there is no airflow and the ambient is already elevated.

Deciding between the three

LCB30 — up to 35 A on 12 AWG. The default for compact lithium packs where the enclosure is tight and the run is short.

LCB40 — the middle size. Larger contact area than LCB30, for heavier wire where 35 A is not enough but the LCB50 body is oversized.

LCB50 — normally on 8 AWG silicone. The largest contact in the family, supplied on 200 °C-rated silicone cable. This is the size for the heaviest pack and motor runs.

When a latch is the whole point

The retention force of ≥ 8.0 kg against an insertion force of ≤ 5.0 kgf means the pair does not separate under vibration without a deliberate release. That is the reason to specify an LCB over an XT:

  • Battery to controller on a moving vehicle
  • Motor to controller on a drive that vibrates
  • Anywhere a friction-fit connector has come loose before

Storage note that matters for silver plating

Silver-plated contacts tarnish. The datasheet is explicit about storage:

  • −10 °C to +40 °C, ≤ 80% RH
  • Keep sealed and out of light
  • Away from sulphides
  • Never handle with bare hands

Tarnish raises contact resistance, and on a 0.6 mΩ part there is little headroom to lose. If your warehouse is humid, bag the parts.

Frequently asked

Is 50 mating cycles enough? Yes, for what the part is for. LCB is a semi-permanent connection — you fit it once and leave it. If the application disconnects daily, this is the wrong family; a battery swap connector rated 3000 cycles is the right one.

Can I get LCB30 on a different gauge? The rating is gauge-specific. Tell us the gauge you need and we will confirm the corresponding current figure rather than assuming it scales.

Does the orange housing mean anything? It is an identification color shared across the family. It is not a rating indicator.


Send us the continuous current, the gauge and the enclosure conditions, and we will recommend the size and confirm the rating from the manufacturer’s documentation.

Need this built to your drawing?

Send the drawing, the gauge and the annual volume — we quote within one working day and sign an NDA before drawings change hands.

Request a quotation

← All technical notes