XT60 vs XT90 vs XT150: choosing by continuous current, not by name
A practical comparison of the three XT body sizes — contact area, real continuous rating, typical wire gauge and where each one is the wrong choice.
The XT family covers most of the 2-pin DC market, and the three sizes people actually specify are XT60, XT90 and XT150. They differ in contact area, housing size and — the part that matters — the continuous current they can carry before temperature rise exceeds the permitted limit.
The comparison that matters
| XT60 / XT60E | XT90 / XT90E | XT150 | |
|---|---|---|---|
| Continuous rating | 35 A max on 12 AWG | 30–50 A, gauge dependent | 60 A AC/DC |
| Rated voltage | 500 V DC | 500 V DC | 500 V AC/DC |
| Contact resistance | ≤ 1.0 mΩ | ≤ 0.6 mΩ (typical) | 20 mΩ max (see note) |
| Body size | 21.3 × 16.0 × 8.1 mm (F) | 24.0 × 21.0 × 19.5 mm | Shell φ10.0 mm, 30.4 mm long |
| Typical wire | 14–12 AWG | 12–10 AWG | 10–8 AWG |
| Mating cycles | ~100 | ~100 | Semi-permanent |
| Ingress protection | IP40 | IP40 | Not rated |
Note on the XT150 contact resistance. The 20 mΩ figure in the Amass drawing (100002PM-1P-66X) is measured over the whole termination, not the contact interface alone. Do not read it as “the XT150 is a worse contact than the XT90” — the larger body carries twice the current.
Choosing in practice
XT60 — up to 35 A. The default for RC packs, e-bikes, small power stations and bench supplies. On 12 AWG it reaches 35 A at 85 K rise. Above that you are relying on short duty cycles, which is not a design method.
XT90 — 30 to 50 A. The contact area is meaningfully larger, and the body accepts 10 AWG. The reason the rating is quoted as a range is that it depends entirely on the gauge you terminate into it: on 12 AWG you get roughly the XT60 figure, on 10 AWG you get closer to 50 A. Fitting an XT90 to thin wire buys nothing.
XT150 — 60 A. Where the current is genuinely high and the connection is semi-permanent: large packs, inverters, traction. At 10 AWG minimum, and normally 8 AWG silicone. The body is big enough that it changes your enclosure design, so it is not a part you fit as an afterthought.
The mistakes we see most
- Using the model number as the rating. XT90 does not mean 90 A. On a 12 AWG lead it is closer to 30 A.
- Upgrading the connector but not the wire. The connector is one link in a thermal chain. Keep the weak link as the wire gauge.
- Assuming XT90 is a drop-in replacement for XT60. It is not — the bodies do not mate. An adapter lead is needed, and that adapter is rated by the smaller end.
- Ignoring the enclosure. All three figures assume free air. In a sealed battery box, derate.
Mating and adapter leads
XT60, XT90 and XT150 do not interchange. Where two systems meet, use an adapter lead and rate it by the smaller connector:
- XT60 female to EC5 — rated 30 A, limited by the XT60 end
- XT60 female to 12 V cigarette plug — rated 10 A, limited by the fused plug
Frequently asked
Can I use an XT90 where the load peaks at 80 A? For very short peaks, possibly, and this is what an “instantaneous” figure would cover. But the published continuous rating is what the thermal design supports. If the average current approaches the peak, step up to an XT150 or a latched LCB.
Which one is best for a battery pack that gets unplugged daily? None of the XT series is designed for daily cycling — they are all around 100 mating cycles. For high cycle counts, use a latched connector: LCB30/50 for two-pin, or the 6+2 plug used in battery swap cabinets, which is rated 3000 cycles.
Tell us the continuous current, the gauge you want and how often it is disconnected, and we will confirm which body and assembly rating fits — in writing.
Need this built to your drawing?
Send the drawing, the gauge and the annual volume — we quote within one working day and sign an NDA before drawings change hands.