Contact resistance matters more than the current rating on the box
Why a 2 mΩ joint at 30 A dissipates nearly 2 W in a space the size of a fingernail, and what mΩ figures on a datasheet actually measure.
A connector’s current rating gets printed on the listing in large type. Its contact resistance is buried in the datasheet, if it appears at all. That is backwards — the resistance is what determines whether the rating holds after a year in service.
The arithmetic is unforgiving
Power dissipated in a contact is I²R. At 30 A:
| Contact resistance | Power dissipated | Effect |
|---|---|---|
| 0.4 mΩ | 0.36 W | Negligible |
| 1.0 mΩ | 0.9 W | Warm to the touch |
| 2.0 mΩ | 1.8 W | Hot spot, discoloration over time |
| 5.0 mΩ | 4.5 W | Housing softening, eventual failure |
The space involved is a few square millimeters. A watt dissipated there is not the same as a watt dissipated along a meter of cable.
This is why a connector can be “rated 30 A” and still fail at 30 A: the rating assumes a contact resistance the part no longer has.
Resistance rises in service
A new contact at 0.6 mΩ does not stay at 0.6 mΩ. Three mechanisms push it up:
Tarnish. Silver plating reacts with sulphur in the air; the resulting film is a poor conductor. This is why storage matters — the LCB datasheet specifies sealed, dark, low- humidity storage and no bare-hand handling.
Fretting. Small relative movement between contact surfaces — from vibration, or thermal expansion — wears through the plating and exposes base metal.
Contamination. Dust, flux residue or skin oils at the interface raise resistance locally.
A part specified at 0.6 mΩ with gold plating holds its value far better than the same part with bare copper, which is why gold appears on connectors that see many cycles or long service.
What datasheet mΩ figures measure
Not all mΩ numbers are comparable. They are measured:
- Across the contact interface only — the theoretically interesting figure
- Terminal to terminal, including the crimp — the practically relevant figure
- Assembly to assembly, including the wire — the number that predicts heating
An XT150 drawing quoting 20 mΩ is measuring a different thing from an LCB30 datasheet quoting 0.6 mΩ. Comparing them directly is meaningless.
When you evaluate a supplier, ask which measurement the figure refers to.
Practical guidance
Match the plating to the cycle count. Gold for many cycles and long service; silver for high current with few cycles; tin for cost-sensitive static joints.
Check the crimp before blaming the contact. A poor crimp can add more resistance than the contact interface itself. Crimp height and pull force are the two things to sample.
Do not judge by the connector alone. The assembly rating already accounts for the whole chain. If your own testing shows heating, the crimp is the first suspect.
Derate in enclosures. All resistance-driven heating is worse without airflow.
Frequently asked
Is lower contact resistance always better? Better, yes; but past a point the gain is irrelevant. Below roughly 1 mΩ at 30 A, the cable’s own resistance dominates.
Does the number of mating cycles change resistance? It does — resistance typically falls slightly on first mating, then rises as plating wears. The cycle rating on a datasheet is where the part is judged to still meet its specification, not where it fails outright.
Why do some connectors specify a maximum rather than a typical? Because the manufacturing spread matters. A maximum of 1.0 mΩ means every part is at or below it; a typical of 0.5 mΩ tells you nothing about the worst one in the batch.
If you need a contact-resistance figure for a specific assembly, tell us the part and the measurement method your incoming inspection uses, and we will return the number in the same terms.
Need this built to your drawing?
Send the drawing, the gauge and the annual volume — we quote within one working day and sign an NDA before drawings change hands.